yanka

I am hoping someone will know the answer to my problem. I'm using Miditron microcontroller with MaxMSP/Jitter and i am unable to get digital signal out using "ctlout". Not even to light a pathetic test LED.

Now, when i open Miditron programmer, i am able to control LED with the "send" option available directly from the programer. However, when i try passing values from my own patch using "ctlout 1" it just doesn't happen. My settings are as follows::

From miditron programmer: When i send 0 that turns LED off, and 1 to turn it on.

Term#1 Mode:DigitalOut Channel:1 Command:Control Change Ctrl#1 Ctrl value-low:1 Ctrl value-high:0 Polarity:positive

From Max Patch: ctrl 1 (sending values directly to the left inlet)

Thank you in advance.Any help would be greatly appreciated.

I am hoping someone will know the answer to my problem. I'm using Miditron microcontroller with MaxMSP/Jitter and i am unable to get digital signal out using "ctlout". Not even to light a pathetic test LED. 

Thank you in advance.Any help would be greatly appreciated. 

miditron-ctlout-doesnt-go-through-please-help

2) Make your object 'ctlout 1 1'. Then send 0/1 into the left inlet.

If that doesn't work, contact me offlist.

>I am hoping someone will know the answer to my problem. I'm using 

>Miditron microcontroller with MaxMSP/Jitter and i am unable to get 

>digital signal out using "ctlout". Not even to light a pathetic test 

>Now, when i open Miditron programmer, i am able to control LED with 

>the "send" option available directly from the programer. However, 

>when i try passing values from my own patch using "ctlout 1" it just 

>doesn't happen. My settings are as follows::

>>From miditron programmer: When i send 0 that turns LED off, and 1 

>Term#1 Mode:DigitalOut Channel:1 Command:Control Change Ctrl#1 Ctrl 

>value-low:1 Ctrl value-high:0 Polarity:positive

>>From Max Patch: ctrl 1 (sending values directly to the left inlet)

>Thank you in advance.Any help would be greatly appreciated.

********************************************

* The Wireless Sensor to MIDI Interface *

At 7:38 PM -0600 5/11/08, Yana wrote:
>Dear all,
>
>I am hoping someone will know the answer to my problem. I'm using 
>Miditron microcontroller with MaxMSP/Jitter and i am unable to get 
>digital signal out using "ctlout". Not even to light a pathetic test 
>LED.
>
>Now, when i open Miditron programmer, i am able to control LED with 
>the "send" option available directly from the programer. However, 
>when i try passing values from my own patch using "ctlout 1" it just 
>doesn't happen. My settings are as follows::
>
>>From miditron programmer: When i send 0 that turns LED off, and 1 
>>to turn it on.
>
>Term#1 Mode:DigitalOut Channel:1 Command:Control Change Ctrl#1 Ctrl 
>value-low:1 Ctrl value-high:0 Polarity:positive
>
>
>>From Max Patch: ctrl 1 (sending values directly to the left inlet)
>
>
>
>Thank you in advance.Any help would be greatly appreciated.
>
>Y
>
>
>

********************************************
* MidiTron                                 *
* The MIDI to Real World Interface         *
*                                          *
* MidiTron Wireless                        *
* The Wireless Sensor to MIDI Interface    *
*                                          *
* Now available from http://miditron.com   *
********************************************


Thank you i will, since the changes didn't seem to make a difference. The MIDItester runs just fine though.

Miditron - ctlout doesn't go through. Please help!