Forums > MaxMSP

[OT] Midi To Yamaha 01V


f.e
October 4, 2006 | 9:11 pm

Does anyone have experience with the 01V and Midi control ? I can’t find
the "midi sheets" anywhere and i don’t know where to find the correct
controller numbers. There’s a few things (.pdf, .xls) on the Yamaha
website, but it’s pretty obfsucated.

Many thanks in advance

f.e


October 4, 2006 | 9:58 pm

A special guest appearance of Don Buchla with TrioMetrik at the Cycling74 event Thursday after AES at Recombinant Media labs.

Don does not get out to play often so this will be a treat. He’ll perform on a fully loaded 200e – an impressive new modular system he has been refining modeled after the classic Buchla 200 series. He played with us at a private concert last Saturday and it was quite wonderful.

Also not listed but appearing with us is Jaron Lanier of VR fame performing on a Thai wind instrument.

We go on first (6:30) so you’ll have to hustle from the show.

Thanks,

Keith

Keith McMillen
BEAM Foundation
http://www.beamfoundation.org/
510.502.5310


October 4, 2006 | 10:08 pm

Salut f.e.,

On 04-oct.-06, at 23:11, f.e wrote:

> Does anyone have experience with the 01V and Midi control ? I can’t
> find the "midi sheets" anywhere and i don’t know where to find the
> correct controller numbers. There’s a few things (.pdf, .xls) on the
> Yamaha website, but it’s pretty obfsucated.

Can’t check now (no 01V at hand, nor the right computer) but I sent
MIDI to the 01V in the past. I don’t know what you’re after, but if I
remember well, most of the parameters were set thru sysex.
If you give me some details, I may have somthing for you tomorrow.

Have a good night (trying to port some obscure C code to Windoze? ;-)

p


October 4, 2006 | 11:32 pm

I’ve got the full .pdf manual and an 01V.

I’ve put it here for you: http://www.speedyshare.com/168837850.html

I would have attached it but it’s too big for the forum 4,777kb.

It’s got brilliant MIDI implementation for a digital mixer, being from that era without USB or Firewire as standard.

Is there anything in particular you need to know?

I might be able to help but it’s been a long time since i actually controlled it with MIDI/used it as a controller!


October 4, 2006 | 11:38 pm

Just had more of a scan through that .pdf and it’s jam packed full of MIDI implementation info…pages and pages of MIDI charts and a whole chapter on implementing MIDI.

It’s mainly control changes, which are all assignable…it’s a bit more limited if you’re trying to transmit from it but it recognises more than most synths i’ve seen!

Anyway, it’s all in the .pdf link!

Hope that helps,
John


October 5, 2006 | 2:00 am

We use the o1v a lot here as both a controller and as a signal
modifier. The most effective, and quickest., way to find out what
MIDI can be controlled is by running MID from the o1v into a midiin
object then through midiparse. As you twiddle the knobs, move the
faders etc you will see what controllers are being effected and
therefore how to control different aspects of the device. You can
also check through the MIDI page on the o1v to get a sense of the
possibilities and then map controllers appropriately.

hope this helps too

Roger

>Just had more of a scan through that .pdf and it’s jam packed full
>of MIDI implementation info…pages and pages of MIDI charts and a
>whole chapter on implementing MIDI.
>
>It’s mainly control changes, which are all assignable…it’s a bit
>more limited if you’re trying to transmit from it but it recognises
>more than most synths i’ve seen!
>
>Anyway, it’s all in the .pdf link!
>
>Hope that helps,
>John
>–
>Imagination is more important than knowledge – A. Einstein
>
>!DSPAM:2000,45244829184731382734229!


Roger Alsop, Phone: (61 3) 9685 9395
Lecturer in Sound, Fax: (61 3) 9685 9356
School of Production, Mob: 0414 246 943
Victorian College of the Arts,
234 St. Kilda RD.,
SouthBank,
Victoria, Australia, 3006 E-Mail:
r.alsop@vca.unimelb.edu.au


October 5, 2006 | 8:06 am

On 4 oct. 06, at 23:11, f.e wrote:

> Does anyone have experience with the 01V and Midi control ? I can’t
> find the "midi sheets" anywhere and i don’t know where to find the
> correct controller numbers. There’s a few things (.pdf, .xls) on the
> Yamaha website, but it’s pretty obfsucated.

If you only want to control basic stuff of the 01v, it is easy: go to
the mixer’s MIDI menu, third page. There you can assign the controller
number you want to faders, mute, pan, etc. Even to effect parameters
(although I remember that some configurations with effects didn’t work
as I expected).
One more thing, make sure that the 01v accepts control ins: midi, page
1.

p

_____________________________
Patrick Delges

Centre de Recherches et de Formation Musicales de Wallonie asbl

http://users.skynet.be/crfmw/max



f.e
October 6, 2006 | 12:19 pm

Thanks a lot, John, that’s very nice of you. I think with your manual
and Patrick’s advices i’ll get my way in :-)

best regards

f.e

john inder wrote:
> I’ve got the full .pdf manual and an 01V.
>
> I’ve put it here for you: http://www.speedyshare.com/168837850.html
>
> I would have attached it but it’s too big for the forum 4,777kb.
>
> It’s got brilliant MIDI implementation for a digital mixer, being from that era without USB or Firewire as standard.
>
> Is there anything in particular you need to know?
>
> I might be able to help but it’s been a long time since i actually controlled it with MIDI/used it as a controller!
>
>
>
>
> –
> Imagination is more important than knowledge – A. Einstein
>
>


October 6, 2006 | 2:01 pm

You’re more than welcome f.e, glad i was able to help.
:-)


Viewing 9 posts - 1 through 9 (of 9 total)