How to adapt hostsync~ frequency
Hello, it’s a naive question i guess but i cannot figure out a simple way to get hostsync~ go slower… i need to synchronize with an host and instead of the quarter notes i need to synchronize to the whole measure beat (e.g. four times slower for 4/4 )..
Just sample hostsync~ output once every 4 beats. There are many objects you could use.
All could be useful for this.
you mean every four samples? Maybe i’m a bit stupid on this problem: if i take a value every four samples i get less values, but still get values from 0 to 1 that repeat four times in the interval of time in need one increase from 0 to 1.
If hostphasor~ goes up 0-1 in one second, i need values from 0-1 in 4 seconds.
Moreover i need a signal not values to drive my other objects, e.g. i don’t want to downsample. But maybe i understood wrong your answer….
Check out rate~
alberto novello wrote:
> Moreover i need a signal not values to drive my other
> objects, e.g. i don’t want to downsample. But maybe i understood
> wrong your answer…. A
hostsync~ is not a signal rate object. If you look at the help patch you will see that the second outlet outputs on the bar whereas the third outlet outputs on the beat.
Did you mean hostphasor~? hostphasor~ outputs a ramp from 0-1 over each beat. Does this help?
----------begin_max5_patcher---------- 664.3ocyW0sbiBBF8Z8of0qSS8CEi1Y5E84Xmc1wnzD1QAGkLMa6z7ruBpIY SMMZMZ5MvHfv46v46GdyzvZoXKsvB8.5mHCi2LMLzCoFvn9aCqzvsQIgE5kY EIRSobo0rp4jzsR83whW3EgoYIz3l4dVvkErWop4A7b65g4aRY7DpTueP8fr X8tHV9m6HNVGVoXirYoM+eVNsnDAgRlf+6bZjrB9XhW4QfbIfpyttA8qi.CO LUCFqmxYgIMmRVnLZMiu5r6kuqpEq2M0u7toopY1.YLQd4gx3G.xWkuveNe0 KKGH1UVt57QjECxx4zWJA3GLbZ7J5tVMZXNIf.9K5nkCAsa43KZ4UKV92LZk YasLjuxZVc+dQSqRChhS.OM035LFDziOtCcGzaFB+QFxcQ6LDzeFpfsRoU+b tQ6o.t5NW2wfahVWdCccjOt92BxABzdVjAQNEQhrCjvkTANdesHpt5f.N9sG Q87NGN5nWHvwde2TXkjKXksDsCaeMw6Yjr2ibm2mX7sXa3fqlT84DQnrKg3v DsR0AOmb8ciuGA111ClV7tAzBni46NJoF+QIuLXRAtAjhi23oUxVGVHx2MTZ wdZi1WwK95NxnjJTxRo4CjU.uqVITUhkxZn5T8SA5jJNCyKh9ZbXTmSP3067 C3JubRsKOoocDT2koVICUgeCJmIPmxbQ65a8+akv3m9DS89oF++oqBwl7nFL z3yhNTwQLsPV9fIUYJGsHU0MGsn0r3XJ+3K1TVblfwk0f3LWdcFSc.RpJKmP HodGzEwjxSGAeCwzzwSpWCcYLELsXxuK5oESqdxqCXBOwtccBSvzhInKXZZ0 S3t32cRb0uCgLUudqOPB64np0D.cgm.NX+WmjBx7cy+AGUwwNC -----------end_max5_patcher-----------
On 10 sept. 08, at 14:42, alberto novello wrote:
> you mean every four samples? Maybe i’m a bit stupid on this problem:
> if i take a value every four samples i get less values, but still
> get values from 0 to 1 that repeat four times in the interval of
> time in need one increase from 0 to 1.
Can’t you simply use [rate~] ?
Centre de Recherches et de Formation Musicales de Wallonie asbl
Yes, use rate~. Rate does what my patch does but I’d completely forgotten about it!
Yeah sorry for the mistake i meant of course hostphasor~…. yesterday was a busy day;)… yeah rate~ its’ perfect i didn’t know it and now everything is easier! Thanks owen and fairesigneaumachiniste
Forums > MaxMSP