BEAP Analog Model Curriculum Outline

From Cycling '74 Wiki
Revision as of 00:55, 26 June 2013 by Darwin Grosse (Talk | contribs)

Jump to: navigation, search



  • What is the Analog Model?
    • Based on modular synthesis techniques.
    • Focuses on subtractive synthesis.
    • Built off of four primary tools:
      • Oscillators
      • Filters
      • Level Controls
      • Modulators

  • Why is this Important?
    • It is the basis for most modular synth techniques.
    • It is also the basis for a lot of synth-based music.
    • It provides a useful way to do sound design iteratively.
    • It sounds good, too!

  • What is necessary for this workshop?
    • A laptop with audio capability.
    • A pair of headphones.

Oscillators and Tone Generation

  • Oscillators are the way that synths make sound. They create repeated waveshapes at a set frequency.
    • Select an Oscillator from the contextual menu (ctrl/right-click, then Paste From | BEAP | Oscillators | Oscillator).
    • An oscillator by itself creates waveforms, but is not routed to our computer's output. For this, we need an Output Module.
    • Select a stereo output from the contextual menu: Paste From | BEAP | Output | Stereo
    • Connect the output of the oscillator to both inputs of the Stereo module.
    • Turn on the DSP (this might need explaining), and you should hear a tone.

  • The two most important setting of the oscillator are the tuning and the waveshape.
    • Change the tuning by adjusting the offset knob on the front of the Oscillator module.
    • Change the waveform by selecting a waveform image in the button matrix.
    • Note how the waveform changes the timbre, but not the pitch, of the oscillator.

  • More than one oscillator can be used at a time to create more interesting tonality.
    • Select another Oscillator from the menu, or copy the existing one by option/alt-dragging the one already on-screen.
    • Select the patchcord going to the right inlet of the Stereo module, then grab the top handle and drag it from the first to the second oscillator.
    • Now you will hear an oscillator in each ear of your headphones. Adjust the offset and waveform in each to verify the changes.

  • In order to have the two oscillators "mix" together, we need to use another device to combine them.
    • Add an audio mixer using the Paste From | BEAP | Mixers | Audio option from the contextual menu.
    • Connect the two oscillators to inputs 1 and 2 of the mixer, then connect the output of the mixer to the two Stereo inputs.
    • Turn up the volume of the mixer channels to hear a mix of the tones. You can alter the volume of each oscillator to create a nicely blended tone.

  • At this point, we are able to hear the oscillators, but it would be nice to change the pitch in a musical way.
    • We need a controller, and will create a virtual keyboard using Paste From | BEAP | Input | Keyboard
    • Connect the CV output to the 1V/Oct inputs of the oscillators. The terminology used here is from the modular synthesis world...
    • Lock the patch and click on the keyboard keys. You should hear the pitch change to match the keyboard notes.

Level Control/Gating with a VCA

  • One of the issues with our current system is that the oscillator tones never turn off.
    • This is how analog oscillators work - they are never really "off", they are only muted.
    • We can have our keyboard mute the signal if we use another module, and the gate output of the keyboard.

  • The VCA - Voltage Controlled Amplifier
    • The purpose of a VCA is to use incoming signal values to adjust the amplitude of a signal. In this case, we will use it to control the volume of the mixer output.
    • Instantiate a VCA, then connect it between the Mixer and the Stereo Output module. The signal will immediately turn off.
    • In order to turn a VCA "on", we need to send it a HIGH value whenever a key is pressed, then a LOW value when the key is released.
    • This is done using the Gate output of the keyboard, which produces exactly those values as we play the keyboard.
    • Connect the Gate output of the keyboard to the Control input of the VCA, then play the keyboard - and you will now hear the sound as expected.

Filtering with an LPF

Modulating with Envelopes and LFO's

Improving the Sound with Effects

Creating Material with Sequencing

Recording your Output


Based on a workshop given at the Currents New Media Festival in 2013 by Darwin Grosse