Dread

Currently trying to send some simple data out of max wirelessly using udpsend, to my adafruit feather m0 wifi board. Now sending data from the microcontroller into max via osc is flawless, but for some reason the examples given to receive data into the controller do not work correctly.

the one example that semi works is the "WiFi UDP Send and Receive String" in the wifi101 examples. If I send a word out of max using this code, I receive that word no problem. However, when sending an integer out, the script prints "int", and if I send 2 integers it prints "list". It seems like it is receiving the values, but it is not able to actually tell me what those values are.

Is there something I need to add in either the max patch or the arduino script to make it read correctly? Arduino code is printed below, and the max patch is literally just banging a integer/integer list into a udpsend.

/*
  WiFi UDP Send and Receive String

 This sketch wait an UDP packet on localPort using a WiFi shield.
 When a packet is received an Acknowledge packet is sent to the client on port remotePort

 Circuit:
 * WiFi shield attached

 created 30 December 2012
 by dlf (Metodo2 srl)

 */


#include <SPI.h>
#include <WiFi101.h>
#include <WiFiUdp.h>

int status = WL_IDLE_STATUS;
#include "arduino_secrets.h" 
///////please enter your sensitive data in the Secret tab/arduino_secrets.h
char ssid[] = SECRET_SSID;        // your network SSID (name)
char pass[] = SECRET_PASS;    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;            // your network key Index number (needed only for WEP)

unsigned int localPort = 2390;      // local port to listen on

char packetBuffer[255]; //buffer to hold incoming packet
char  ReplyBuffer[] = "acknowledged";       // a string to send back

WiFiUDP Udp;

void setup() {
  //Initialize serial and wait for port to open:
  Serial.begin(9600);
  while (!Serial) {
    ; // wait for serial port to connect. Needed for native USB port only
  }

  // check for the presence of the shield:
  if (WiFi.status() == WL_NO_SHIELD) {
    Serial.println("WiFi shield not present");
    // don't continue:
    while (true);
  }

  // attempt to connect to WiFi network:
  while ( status != WL_CONNECTED) {
    Serial.print("Attempting to connect to SSID: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    status = WiFi.begin(ssid, pass);

    // wait 10 seconds for connection:
    delay(10000);
  }
  Serial.println("Connected to wifi");
  printWiFiStatus();

  Serial.println("\nStarting connection to server...");
  // if you get a connection, report back via serial:
  Udp.begin(localPort);
}

void loop() {

  // if there's data available, read a packet
  int packetSize = Udp.parsePacket();
  if (packetSize)
  {
    Serial.print("Received packet of size ");
    Serial.println(packetSize);
    Serial.print("From ");
    IPAddress remoteIp = Udp.remoteIP();
    Serial.print(remoteIp);
    Serial.print(", port ");
    Serial.println(Udp.remotePort());

    // read the packet into packetBufffer
    int len = Udp.read(packetBuffer, 255);
    if (len > 0) packetBuffer[len] = 0;
    Serial.println("Contents:");
    Serial.println(packetBuffer);

    // send a reply, to the IP address and port that sent us the packet we received
    Udp.beginPacket(Udp.remoteIP(), Udp.remotePort());
    Udp.write(ReplyBuffer);
    Udp.endPacket();
  }
}


void printWiFiStatus() {
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");
  Serial.println(WiFi.SSID());

  // print your WiFi shield's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");
  Serial.println(ip);

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.print(rssi);
  Serial.println(" dBm");
}

the one example that semi works is the "WiFi UDP Send and Receive String" in the wifi101 examples. If I send a word out of max using this code, I receive that word no problem. However, when sending an integer out, the script prints "int", and if I send 2 integers it prints "list". It seems like it is receiving the values, but it is not able to actually tell me what those values are. 

Is there something I need to add in either the max patch or the arduino script to make it read correctly? Arduino code is printed below, and the max patch is literally just banging a integer/integer list into a udpsend. 

Evening all, 
Currently trying to send some simple data out of max wirelessly using udpsend, to my adafruit feather m0 wifi board. Now sendi

Max to arduino via UDP (adafruit feather M0 wifi)